Cast Aluminum Brick & Block Ventilators are made of high corrosion resistant alloy #319. All castings come with aluminum insect screen with 7 x 7" mesh. The block ventilators are designed with a deep louvered face and a continuous water stop set far back on the inside of the casting, a combination that prevents water from entering the building. There is a drip at the top and bottom of the casting to prevent water staining or sprawling of the brick.
  • Minimum .125” thickness
  • Mill Finish
  • Continuous weepage on bottom
  • 1" deep overlapping blade
  • Water stop at rear
  • One piece molded unit
  • Load Bearing
   

Extruded Ventilators are the answer where a fine finish is a requisite, where a superior ventilator is required at a minimum cost. The ventilators are designed with a deep louvered overlapping blade, the blade itself has a storm stop at the rear, with a high waterstop at the rear of ventilator. Our ventilators can be used as Industrial Ventilators or Commercial Ventilators as well.
  • Available in any special size to suit any job design
  • All extruded sections
  • Minimum .125” thickness
  • 1" deep overlapping blade
  • 204-R1 Clear Anodized finish standard
  • Made in any length up to 8 ft. without front mullions—continuous blade effect
  • Continuous weepage on bottom
  • Overlapping blades
  • All blades at 45 degrees
  • Can also be used as Industrial & Commercial Ventilators
  • **Add 1/4" to Order Height to Allow For Ribs
   

Extruded Ventilators make possible simplified installation in existing walls. Chopped-out hole need not be “finished”. An attractive appearance is assured by flange.

  • * Available in any special size to suit any job design
  • All extruded sections
  • Minimum .125” thickness
  • 1" deep overlapping blade
  • 204-R1 Clear Anodized finish standard
  • Made in any length up to 8 ft. without front mullions
    — continuous blade effect
  • Continuous weepage on bottom
  • Overlapping blades
  • All blades at 45°
  • ** Add 1/4" to Order Width For Fastener Heads

Empire Stationary Aluminum Louvers are used for either intake or exhaust on homes, factories, restaurants, barns, theaters, ships, etc. They are ideal for power exhaust with the simple removal of the screen.*

Attractive in appearance, these precision-built louvers are storm-proof, rustproof, and bird proof. They provide positive ventilation with more free area. No servicing is required.

Empire louvers are all-riveted into one rigid unit and have a 1 1/4" mounting flange for easy installation. The louver frame is 2" deep. FHA approved #8 mesh is supplied unless otherwise specified.

Louvers are available with the blades running either the short or the long way. When ordering, designate width first.

Louvers can be made in any size up to forty-eight inches in two inch increments, to allow for even distribution of blades. Prices on application.

All our louvers are available in Galvanized Steel, Copper, Lead-Coated Copper, and Stainless Steel.

   

The Empire roof louver is designed for all types and pitches of roofs.

The one piece base with deflector baffle and domed top combine to make this a weatherproof louver with maximum air discharge. #60 Available in aluminum or copper. #40 Aluminum Only

   

The Empire Soffet Ventilator is a rugged under eaves ventilator. All aluminum, FHA approved #8 Aluminum mesh.

These can be shipped by carton lots only.

   

The Empire Strip Ventilator is perfect for under eaves ventilation. All aluminum construction .125" X 1".

These can be shipped by carton lots only.

   


Empire Ventilation Equipment Co., Inc. - Est. 1933

35-39 Vernon Boulevard, Long Island City, NY 11106  |   All of our products are proudly MADE IN THE USA

About Us   |    Contact Us   |    Log-In   |    View Shopping Cart

Accessories Bases Louvers Ventilators / Spring Registers / Fans
1/2“ Mesh Screens
Insect Screens
Dampers For Syphon/Eveco
Dampers For Turbine Ventilators
Adjustable Bases
Economy Bases
Standard Mounting Bases
• Flat Bases
• Ridge Roof Bases
• Curb Bases
• Slope Roof Base
Cast Aluminum Ventilators
Extruded Aluminum Ventilators
Flange Extruded Ventilators
Flush-Flange Louvers
Roof Louvers
Soffets
Strip Ventilators
Eveco Ventilators
Insul-Ventilators
Syphon Ventilators
Turbine Ventilators
Booster Fans
Spring Register

© Copyright 2014. Empire Ventilation Equipment Co., Inc. All Rights Reserved. Site Designed and Maintained by Rapport Associates, Ltd.

Eveco Ventilators
Insul-Ventilators
Syphon Ventilators
Turbine Ventilators
1/2“ Mesh Screens
Insect Screens
Dampers For Syphon or Eveco
Dampers For Turbine Ventilators
Adjustable Bases
Economy Bases
Standard Mounting Bases
• Flat Bases
• Ridge Roof Bases
• Curb Bases
• Slope Roof Base
Booster Fans
Cast Aluminum Ventilators
Extruded Aluminum Ventilators
Flange Extruded Ventilators
Flush-Flange Louvers
Roof Louvers
Soffets
Strip Ventilators
Spring Register
Turbine Repair Kits
About Us    |    Pressroom    |    Contact    |    Building Codes   |    Blog
Home    |    Log In    |    Shopping Cart